| 品牌 : | 品贊/G-Switch | 型號 : | GT-TC018X-H035- |
| 高電壓 : | 50mA.12V DC | 額定發熱電流 : | 50mA.12V DC |
| 用途 : | 影音產品.數碼產品.遙控器.通 | 產品認證 : | ROHS |
| 物料編號 : | GT-TC018X-H035- | 加工定制 : | 是 |
| 貨號 : | GT-TC018X-H035- |
產品描述：
產品名稱：側按輕觸開關
產品規格：2×4×3.5mm?
產品高度：H035=3.5mm
生產廠家：品贊/G-Switch
產品型號：GT-TC018X-H035-LX
產品力度：A=160gf、B=250gf、E=140gf
產品壽命：L05=50,000 Cycles、L08=80,000 Cycles
基本參數：
工作溫度范圍Operating temperature range：-30to+85額定電流Rating：50mA.12V DC
絕緣電阻Insulation resistance:：100MΩ min.100V DC
介電強度Dielectric strength： 250V AC for 1 min
接觸電阻Contact resistance:：100m Ω max.
產品應用范圍：
1.影音產品：MP3、MP4、DVD.音響；
2.數碼產品：數碼相機、數碼攝像機等；
3.遙控器：車輛、點卷門、家庭防盜產品之遙控器；
4.通訊產品：手機、車載話機、電話機、樓宇設備、PDA等；
5.家用電器：電視機、微波爐、電飯煲、電風、電子人體秤、電子脂肪秤、電子廚房秤等；
6.安防產品：可視對講機、監視器等；
7.玩具：電子玩具等；
8.電腦產品：攝像頭、錄音筆等；
9.健身器材：跑度機、按摩椅等；
10.醫療器材：血壓計、體溫計、醫院呼叫系統等；
11.其他：驗鈔筆、雷射筆等。
尺寸圖
規格參數
| 6.PERFORMANCE性能 6.1?Electrical電氣 | ||
| Item項目 | Test?Condition測試條件 | Requirements要求 |
| 6.1.1. Contact?Resistance 接觸電阻 | Applying?astatic?load?twice?the?actuating?force?to?the center?of?the?stem,measurements?shall?be?made with?a??1?kHz?small-current?contact?resistance?meter. 用兩倍的動作力作靜負載施加于按鈕的中心,并用1千赫 小電流接觸電阻儀測量 | 100?m?ohm?max. |
| 6.1.2. Insulation?Resistance 絕緣電阻 | Measurements?shall?be?made?following?application?of? DC100V?potintial?across?terminals?and?across?terminals? and?frame?for?one?minute. 在端子與端子之間,端子與外殼之間施加DC100V,一分鐘 | 100?M?ohm?min. |
| 6.1.3. Dielectric?witstanding? voltage 電氣耐壓 | AC250V(50Hz?or60Hz)?shall?be?applied?across?terminals and?across?terminals?and?frame?for?one?minute. ?在端子與端子之間,端子與外殼之間施加AC250V(50HZ-60HZ) | There?shall?be?no ?breakdown. 沒有擊穿 |
| 6.1.4. Bounce 抖動 | Lightly?striking?the?center?of?the?stem?at?a?rate?encountered ?in?normal?use?(3?to?4?operations?per?sec.), Bounce?shall?be?tested?at?“ON”and?“OFF”.? 在正常使用中(以每秒3-4次周期)輕輕地在手柄中心加力,在通 與斷瞬間測試抖動  ? | ? ?????5??m?sec?max. |
6.2Mechanical機械特性 ? | ||
| Item項目 | Test?Condition?試驗條件 | Requirements?規?格 |
| 6.2.1. Actuating?Force 動作力 | Placing?the?switch?such?that?the?direction?of?switch? operation?is?vertical?and?then?gradually? increasing?the?load?applied?to?the?center?of? the?stem,?the?maximum?load?required?for? the?stem?to?come?to?a?stop?shall?be?measured. 開關的動作方向為垂直放置開關向推柄中心逐漸地 增加負荷直到推柄停止時所測量的 負荷 | 180?±??50??gf?or 250?±??50??gf ? |
| 6.2.2. Travel 行程 | Placing?the?switch?such?that?the?direction?of?switch ?operation?is?vertical?and?then?applying ?a?static?load?twice?the?actuating?force?to?the? center?of?the?stem,the?travel?distance?for?the ?stem?to?come?to?a?stop?shall?be?measured.? 開關的動作方向為垂直放置開關, 并以雙倍動作力的靜負荷作用推柄中心,測量推柄從 開始到停止的行程距離 | ?0.25?±?0.1mm |
| 6.2.3. Return?Force 返回力 | The?sample?switch?is?installed?such?that?the ?direction?of?switch?operation?is?vertical?and, upon?depression?of?the?stem?in?its?center?the ?whole?travel?distance?,the?force?of?the ?stem?to?return?to?its?free?position?shall?be?measured. ?開關的動作方向為垂直放置開關, 在已有行程的推柄中心向上減小壓力,推柄回到自由位置 時所測量到的力 | ??45??gf??min |
| 6.2.4. Stop?Strength 靜止強度 | Placing?the?switch?such?that?the?direction?of? switch?operation?is?vertical,a?static?load?of?? ?3?kgf?shall?be?applied?in?the?direction?of? stem?operation?for?a?period?of?60?seconds.? 開關的動作方向為垂直放置開關,在推柄動作方向施加 3KG的靜負荷,60秒時間 | There?shall?be?no?sign?of?damage? mechanically?and?electrically. 無機械的和電氣的損傷跡象 |
| 6.2.5. Stem?Strength 推柄的強度 | Placing?the?switch?such?that?the?direction?of? switch?operation?is?vertical, ?the?maximum?force?to?withstand?a? pull?applied?oppsite?to?the?direction?of?stem?operation shall?be?measured.? 開關的動作方向為垂直放置開關, 從推柄動作方向反方向施加拉力所測量到的 承受力 | ??????????????3???kgf |
| 6.3Environmental環境 | ||
| Item項目 | Test?Condition測試條件 | Requirements要求 |
| 6.3.1. Resistance?to?Low? Temperatures 耐低溫 | Following?the?test?set?forth?below?the?sample?shall?be left?in?normal?temperature?and?humidity?conditions?for one?hour?before?measurements?are?made: 樣品按下列條件進行耐低溫試驗,測試前在正常溫度和濕 度條件下放置1小時
| Item?6.1 Item?6.?2.1 Item?6.2.2 ? |
| 6.3.2. Heat?Resistance 耐熱 ? ? | Following?the?test?set?forth?below?the?sample?shall be?left?in?normal?temperature?and?humidity?conditions for?one?hour?before?measurements?are?made:? 樣品按下列條件進行耐熱試驗,測試前在正常溫度和濕度 條件下放置1小時 (1)Temperature:??80±2??溫??度 (2)??????Time:??96?hours??時??間 | Item?6.1 Item?6.?2.1 Item?6.2.2 |
| ? 6.3.3. Moisture? Resistance 耐潮濕 ? ? ? | Following?the?test?set?forth?below?the?sample?shall?be left?in?normal?temperature?and?humidity?conditions?for? one?hour?before?measurements?are?made:? 樣品按下列條件進行耐潮濕試驗,測試前在正常溫度和濕度 條件下放置1小時
| Contact?resistance: 500?m?ohm?max接觸電阻 Insulation?resistance? 10?M?ohm?min.? 絕緣電阻 Item?6.1.3 Item?6.2.1 Item?6.2.2 |
| 6.3Environmental環境 | ||
| Item項目 | Test?Condition測試條件 | Requirements要求 |
| 6.3.1. Resistance?to?Low? Temperatures 耐低溫 | Following?the?test?set?forth?below?the ?sample?shall?be?left?in?normal? temperature?and?humidity?conditions ?for?one?hour?before?measurements?are?made: 樣品按下列條件進行耐低溫試驗,測試前在正常溫度和濕度 條件下放置1小時 (1)?Temperature:??-30±2??????溫??度 (2)???????Time:??96?hours???????時??間 (3)?Water?drops?shall?be?removed.??擦除水珠 | Item?6.1 Item?6.?2.1 Item?6.2.2 ? |
| 6.3.2. Heat?Resistance 耐熱 ? ? | Following?the?test?set?forth?below?the?sample?shall be?left?in?normal?temperature?and?humidity?conditions ?for?one?hour?before?measurements?are?made: 樣品按下列條件進行耐熱試驗,測試前在正常溫度和濕度 條件下放置1小時 (1)Temperature:??80±2??溫??度 (2)??????Time:??96?hours??時??間 | Item?6.1 Item?6.?2.1 Item?6.2.2 |
| ? 6.3.3. Moisture? Resistance 耐潮濕 ? ? ? | Following?the?test?set?forth?below?the?sample? shall?be?left?in?normal?temperature?and?humidity conditions?for?one?hour?before?measurements are?made:? 樣品按下列條件進行耐潮濕試驗,測試前在正常溫度 和濕度條件下放置1小時 (1)?????Temperature:??60±2???溫度 (2)?Relative?humidity:??90?to?95?相對濕度 (3)???????????Time:??96?hours???時?間 (4)?Water?drops?shall?be?removed.??擦除水珠 | Contact?resistance:500?m?ohm?max接觸電阻 Insulation?resistance?10?M?ohm?min.?絕緣電阻 Item?6.1.3 Item?6.2.1 Item?6.2.2 |
| 6.4Endurance耐久性 | ||
| Item項目 | Test?Condition測試條件 | Requirements要求 |
| 6.4.1. Operating?Life 動作壽命 | Measurements?shall?be?made?following?the?test?set?forth?below: 按下列條件 進行壽命試驗 (1)DC?5V?5mA?resistive?load.??DC?5V?5mA?阻性負載 (2)Rate?of?operation:2?to?3?operations?per?second? ? ? ?動作頻率:2-3次/每秒 (3)Depression:??180???gf?減壓力 (4)Cycles?of?operation:??5×104?cycles??動作次數:?5×104次 | Contact?resistance:?1?Ω?max.? 接觸電阻 Insulation?resistance?:?? 10??M?ohm?min.? 絕緣電阻 Actuating?force:?動作力 +??30?or-??30of? initial?force.??±30初始動作力 Item?6.1.3 tem?6.?2.2 |
| ? 6.4.2. Vibration Resistance 耐振動 ? ? ? | Measurements?shall?be?made?following?the?test?set?forth?below:? 按下列條件進行抗振動試驗 (1)Range?of?oscillation:10?to?55Hz?頻率范圍 (2)Amplitude,pk-to-pk:1.5?mm????振幅:?峰-峰1.5mm (3)Cycle?of?sweep:?10-55-10Hz?in?one?minute,approx. 掃描周期:?10-55-10Hz約一分鐘內 (4)Mode?of?sweep?:Logarithmically?sweep?or?uniform?sweep.?? 掃描方式:對數掃描式恒定掃描 (1)?Direction?of?oscillation:?振動方向 Three?mutually?perpendicular?directions,including?the? directionof?stem?travel.? 3個相互垂直方向,包括推柄行程方向 (2)?Duration?of?testing:?持續時間 2?hours?each?,for?a?total?of?6hours.每方向2小時.共6小時 | ? Item?6.1 Item?6.2.1 Item?6.2.2 |
| ? 6.4.3. Impact?Shock Resistance 抗沖擊 | Measurements?shall?be?made?following?the?test? set?forth?below:? 按下列條件進行沖擊試驗 (1)Acceleration:80g?加速度 (2)Cycles?of?test?:3?cycles?each?in?6directions,?for?a ?total?of?18cycles? 試驗次數：每個方向3次,6個方向共18次 ????????? ? | ? Item?6.1 Item?6.2.1 Item?6.2.2 |
| 7.?Environmental??Endurance?環境耐久性? | ||
| Item項目 | Test?Condition測試條件 | Requirements要求 |
| 7.1. High?Temperature? Cycling 高溫循環 | Foeeowing?ten?cycles?of?high?temperature?test? .Saupee?shall?be?Place?in ?Normae?temperature?and?humidity? Conditious?for?one?hour?before ?measurements?are?made.?During?this?test,? water?drops?shall?be?removed. 樣品按下列條件進行高低溫循環試驗, 測試前在正常溫度和溫度條件下放置1小時,除去水珠 (1)????Temperature(溫度)：-30°80(2)????Cycling(周期)：Ten?cycles?(10個周期)  | ? ? ? Item?6.1 Item?6.?2.1 Item?6.2.2 |
| 7.2 Moisture? Resistance 耐潮濕 ? ? ? | Following?the?test?set?forth?below?the?sample shall?be?left?in?normal?temperature?and?humidity conditions?for?one?hourbefore?measurements are?made:? 樣品按下列條件進行耐潮濕試驗, 測試前在正常溫度和濕度條件下放置1小時 (1)????Temperature:?85±2???溫度 (2)Relative?humidity:??80?to?85?相對濕度 (3)??????????Time:?500?hours???時?間 (3)?Water?drops?shall?be?removed.??擦除水珠 | Contact?resistance:50?m?ohm?max 接觸電阻 Insulation?resistance?10?M?ohm?min.? 絕緣電阻 Item?6.1.3 Item?6.2.1 Item?6.2.2 ? ? ? |
| 8.Use??Endurance?使用耐久性 | ||
| Item項目 | Test?Condition測試條件 | Requirements要求 |
| 8.1 Solderability 焊接性 | Oven?Temperature:235±5，Time:?5S±1S 錫爐溫度：235±5??時間:5秒±1秒 ????????? | Tin?Area:90％ 焊接面積90％以上 ? |
| 8.2 patience?high?temperature 焊接耐熱性 ? | Preheat:?Temperature?on?the?copper?foil?surface ?should?reach?180,?2±0.3?minutes?after The?P.W.B?entered?into?the?soldering?equipment 預熱：在P.W.B(印刷線路板)進入焊接設備后， 2±0.3分鐘內銅箔表面要達到180Soldering?heat:?Temperature?on?the?copper? foil?surface?should?reach?the?peak?temperature?of 260?within?5?seconds?after?the? P.B.W?entered?into?soldering?heat?zone. 焊接溫度：?在P.W.B(印刷線路板)進入焊接溫區5秒內， 銅箔表面達到峰值溫度260?  | ? 表面無起泡,變型 Surface?of?plastics? don’t?frothed?And? formed |
輕觸開關注意事項：
9.?Other?precautions其他注意事項
(1)?Following?the?soldering?process,do?not?try?to?clean?the?switch?with?a?solvent?or?the?like.
進行焊接過程中，不可以用溶劑或類似品清洗開關
(2)?Safeguard?the?switch?assembly?against?flux?penetration?from?its?topside.
防止助焊劑從開關的頂端滲入
(3)?Please?have?the?products?keep?in?close?status?and?the?storage?time?is?90?days?guaranty?after
? ? ? ?delivering?the?goods?at?most.
聲明：有關于產品的單價，規格、參數、壽命、工作溫度、手感、防水等級等數據，只代表品贊電子內部的測試結果予參考，如需詳細了解，請聯系品贊業務部。
